Due to popular demand on another thread (a couple of people asked me!) I have decided to release my design of a combined phone holder and support foot for the Anafi Sky Controller 3.
The piece is 3D printed and it fits over the arm, provides a safe support for a phone It also acts as a protector for the USB-A socket by stopping the lead from the controller to the phone from resting on the ground when the controller is put down. The support is fitted to the controller by slightly extending the arm, placing the support over the thinner section of the arm and then sliding it down to the bottom.
I have 3D printed the piece in ABS with a layer height of 0.2mm and then, after removing any “Elephant’s Foot” from where it was on the print bed and checking that it fitted the controller arm I placed it in a cold acetone vapour bath at room temperature of about 20 deg C for one hour to give it a glossy surface. I then glued, with CA, a small piece of rubber self amalgamating tape to the phone support to give it a good grip.
In the photos my phone is off centre due to the Moto G5 having its power button half way down one side.
This .stl file is available HERE (A version with a slightly longer platform is available HERE )and is offered to the ParrotPilots community on a “not for profit” basis accepting that not all of the community have access to a 3D printer and that users can offer to supply these items in their country for the cost of printing and postage. It is also supplied “as is” and I accept no responsibility for any problems such as damaged phones, cases or pride.
![IMG_20190913_164515233[1].jpg](https://parrotpilots.com/data/attachments/2/2737-28fbb61a7edb2eef85978f613b627b90.jpg?hash=KPu2Gn7bLu "IMG_20190913_164515233[1].jpg")
![20190913_192254[1].jpg](https://parrotpilots.com/data/attachments/2/2738-e5c0260895a870abe79cfa793c97140b.jpg?hash=5cAmCJWocK "20190913_192254[1].jpg")
![20190913_192418[1].jpg](https://parrotpilots.com/data/attachments/2/2739-bc1b3c0e42986764cf19a077dff9329c.jpg?hash=vBs8DkKYZ2 "20190913_192418[1].jpg")
The piece is 3D printed and it fits over the arm, provides a safe support for a phone It also acts as a protector for the USB-A socket by stopping the lead from the controller to the phone from resting on the ground when the controller is put down. The support is fitted to the controller by slightly extending the arm, placing the support over the thinner section of the arm and then sliding it down to the bottom.
I have 3D printed the piece in ABS with a layer height of 0.2mm and then, after removing any “Elephant’s Foot” from where it was on the print bed and checking that it fitted the controller arm I placed it in a cold acetone vapour bath at room temperature of about 20 deg C for one hour to give it a glossy surface. I then glued, with CA, a small piece of rubber self amalgamating tape to the phone support to give it a good grip.
In the photos my phone is off centre due to the Moto G5 having its power button half way down one side.
This .stl file is available HERE (A version with a slightly longer platform is available HERE )and is offered to the ParrotPilots community on a “not for profit” basis accepting that not all of the community have access to a 3D printer and that users can offer to supply these items in their country for the cost of printing and postage. It is also supplied “as is” and I accept no responsibility for any problems such as damaged phones, cases or pride.
Last edited:
![IMG_20190914_173712242[1].jpg](https://parrotpilots.com/data/attachments/2/2745-11e861e2cd65531b9c73fd4338ea42e9.jpg?hash=Eehh4s1lUx "IMG_20190914_173712242[1].jpg")
